mirror of
https://github.com/genuinetools/reg.git
synced 2024-08-22 06:30:23 -04:00
73 lines
2.8 KiB
Go
73 lines
2.8 KiB
Go
package configs
|
|
|
|
// Network defines configuration for a container's networking stack
|
|
//
|
|
// The network configuration can be omitted from a container causing the
|
|
// container to be setup with the host's networking stack
|
|
type Network struct {
|
|
// Type sets the networks type, commonly veth and loopback
|
|
Type string `json:"type"`
|
|
|
|
// Name of the network interface
|
|
Name string `json:"name"`
|
|
|
|
// The bridge to use.
|
|
Bridge string `json:"bridge"`
|
|
|
|
// MacAddress contains the MAC address to set on the network interface
|
|
MacAddress string `json:"mac_address"`
|
|
|
|
// Address contains the IPv4 and mask to set on the network interface
|
|
Address string `json:"address"`
|
|
|
|
// Gateway sets the gateway address that is used as the default for the interface
|
|
Gateway string `json:"gateway"`
|
|
|
|
// IPv6Address contains the IPv6 and mask to set on the network interface
|
|
IPv6Address string `json:"ipv6_address"`
|
|
|
|
// IPv6Gateway sets the ipv6 gateway address that is used as the default for the interface
|
|
IPv6Gateway string `json:"ipv6_gateway"`
|
|
|
|
// Mtu sets the mtu value for the interface and will be mirrored on both the host and
|
|
// container's interfaces if a pair is created, specifically in the case of type veth
|
|
// Note: This does not apply to loopback interfaces.
|
|
Mtu int `json:"mtu"`
|
|
|
|
// TxQueueLen sets the tx_queuelen value for the interface and will be mirrored on both the host and
|
|
// container's interfaces if a pair is created, specifically in the case of type veth
|
|
// Note: This does not apply to loopback interfaces.
|
|
TxQueueLen int `json:"txqueuelen"`
|
|
|
|
// HostInterfaceName is a unique name of a veth pair that resides on in the host interface of the
|
|
// container.
|
|
HostInterfaceName string `json:"host_interface_name"`
|
|
|
|
// HairpinMode specifies if hairpin NAT should be enabled on the virtual interface
|
|
// bridge port in the case of type veth
|
|
// Note: This is unsupported on some systems.
|
|
// Note: This does not apply to loopback interfaces.
|
|
HairpinMode bool `json:"hairpin_mode"`
|
|
}
|
|
|
|
// Routes can be specified to create entries in the route table as the container is started
|
|
//
|
|
// All of destination, source, and gateway should be either IPv4 or IPv6.
|
|
// One of the three options must be present, and omitted entries will use their
|
|
// IP family default for the route table. For IPv4 for example, setting the
|
|
// gateway to 1.2.3.4 and the interface to eth0 will set up a standard
|
|
// destination of 0.0.0.0(or *) when viewed in the route table.
|
|
type Route struct {
|
|
// Sets the destination and mask, should be a CIDR. Accepts IPv4 and IPv6
|
|
Destination string `json:"destination"`
|
|
|
|
// Sets the source and mask, should be a CIDR. Accepts IPv4 and IPv6
|
|
Source string `json:"source"`
|
|
|
|
// Sets the gateway. Accepts IPv4 and IPv6
|
|
Gateway string `json:"gateway"`
|
|
|
|
// The device to set this route up for, for example: eth0
|
|
InterfaceName string `json:"interface_name"`
|
|
}
|